MuxLab 4K HDMI/ST 2110 over IP Uncompressed Multimode Fiber Transmitter
Product Highlights:
- Integrate 4K HDMI into HDMI/IP Workflows
- 4K30 4:4:4 8-Bit Uncompressed Extension
- 1312' Multimode OM4/LC Fiber Distance
- Multipoint Transmission via 10G Networks
- 1G Ethernet Switch Port with PoE
- RS-232 Connector
- REST API Support
- SMPTE ST 2110 Support
- MuxLab 4K HDMI/ST 2110 over IP Uncompressed Multimode Fiber Transmitter
- Power Supply
- Limited 3-Year Warranty
MuxLab 4K HDMI/ST 2110 over IP Uncompressed Multimode Fiber Transmitter
MuxLab 500774-TX-MM 4K HDMI/ST 2110 over IP Uncompressed Multimode Fiber Transmitter MuxLab's 4K HDMI/ST 2110 over IP Uncompressed Multimode Fiber Transmitter allows integrating basic 4K HDMI devices into broadcast environments for hybrid HDMI/IP workflows, enabling broadcasters to have a single IP infrastructure instead of two separate ones. Up to hundreds of these transmitter and optional receiver units can be set up in a single workflow, depending on network bandwidth.
Using optional duplex multimode OM4 fiber cabling with LC connectors, the gateway transmitter extends a 4K30 4:4:4 8-bit uncompressed signal up to 1312' in a point-to-point connection to the corresponding 500774-RX-MM receiver, sold separately. Alternatively, single duplex multimode OM3 cabling with LC connectors transmits the signal up to 984'. Point-to-multipoint and multipoint-to-multipoint configurations can also be set up by connecting to a 10G Ethernet network. The transmitter features a 1G Ethernet switch port with PoE for connecting additional network devices, and has an RS-232 Phoenix connector for remote control of end-point devices. The transmitter supports the SMPTE ST 2110 standard and REST API for third-party serial management.
Key Features
- Integrates 4K HDMI devices into broadcast environments for hybrid HDMI/IP workflows
- Extends a 4K30 HDMI 4:4:4 8-bit uncompressed signal up to 1312' with no latency in a point-to-point setup over duplex multimode OM4 fiber cabling with LC connectors (or up to 984' over single duplex multimode OM3 cabling)
- Point-to-multipoint and multipoint-to-multipoint configurations supported via connection to a 10G Ethernet network
- 1G Ethernet switch port with PoE for connecting additional network devices
- RS-232 Phoenix connector
- Support for SMPTE ST 2110 standard
- REST API support for third-party serial control
| MuxLab TX-MM Specs |
|---|
| Interfaces |
|---|
| Input Connectors |
1 x HDMI (HDMI 1.4) |
| Embedded Audio Input |
HDMI |
| Output Connectors |
2 x LC |
| Other I/O |
1 x 3.5 mm Audio Line
1 x RJ45
1 x 3-Pin Euroblock RS-232 |
| Standards |
|---|
| Video Standard Compliance |
SMPTE ST-2110 |
| Transmission |
|---|
| Max Transmission Distance |
UHD 4K at 30 Hz:
1312.3' / 400 m (via Multi-Mode Fiber) |
| Video Format |
HDMI (8-Bit 4:4:4)
UHD 4K: 30 fps |
| Supported Cable Types |
Multimode Fiber |
| Power |
|---|
| Power Consumption |
Device: (15 W) |
| Environmental |
|---|
| Operating Humidity |
95% |
| General |
|---|
| Certifications |
CE, FCC, RoHS, as per Manufacturer |
| Dimensions |
7 x 4.4 x 1" / 17.8 x 11.2 x 2.5 cm |
| Weight |
1.5 lb / 680 g |
